無法在Arduino Uno R3中使用PubSubClient.h接收訂閱的消息

Question

#include "SPI.h"
#include “WiFiEsp.h”
#include  <WiFiEspClient.h>
#include “SoftwareSerial.h”
#include <PubSubClient.h>
#include <WiFiEspUdp.h>

float temp=0;
int tempPin = 0;
int isClientConnected = 0;

char data[80];
char ssid[] = “SSID”; // your network SSID (name)
char pass[] = “PASSWORD”; // your network password

int status = WL_IDLE_STATUS; // the Wifi radio’s status
char deviceName = “ArduinoClient1”;

IPAddress server(xxx,xxx,xxx,xxx); //MQTT server IP
IPAddress ip(192,168,43,200);

void callback(char* topic, byte* payload, unsigned int length) {
    Serial.print(“Message arrived [“);
    Serial.print(topic);
    Serial.print(“] “);
    for (int i=0;i<length;i++) {
        Serial.print((char)payload[i]);
    }
    Serial.println("-");
}

// Emulate Serial1 on pins 6/7 if not present
WiFiEspClient espClient;
PubSubClient client(espClient);

SoftwareSerial Serial1(6,7); // RX, TX

void setup(){
    Serial.begin(9600);
    Serial1.begin(9600);
    WiFi.init(&Serial1);
    WiFi.config(ip);
    if (WiFi.status() == WL_NO_SHIELD) {
       Serial.println("WiFi shield not present");
       while (true);
    }

    while ( status != WL_CONNECTED) {
       Serial.print("Attemptingonnect to WPA SSID: ");
       Serial.println(ssid);
       status = WiFi.begin(ssid, pass);
       Serial.print("WiFius : ");
       Serial.println(status);
    }

    //connect to MQTT server
    client.setServer(server, 1883);
    client.setCallback(callback);
    isClientConnected = client.connect(deviceName);
    Serial.println("+++++++");
    Serial.print("isClientConnected;
    Serial.println(isClientConnected);
    Serial.print("client.state");
    Serial.println(client.state());

    if (isClientConnected) {
        Serial.println("Connected…..");
        client.publish("status","Welcome to ISG");
        client.subscribe("isg/demoPublish/rpi/ardTempWarn"); 
        //Not able to recieve for this subscribed topic on Arduino Uno Only if I   
        //print it returns 1

    }
}

void loop() {
    temp = (5.0 * analogRead(tempPin) * 100.0) / 1024;
    Serial.print(" temp : " );
    Serial.println(temp);
    Serial.print("client.connected);
    Serial.println(client.connected());
    if (!client.connected()) {
            reconnect();
    }
    client.publish("isg/demoPublish/ard1/tempLM35",String(temp).c_str()); 
    // able to receive data at other         
    // clients like RPI,Web using Mosquitto broker

    client.loop();
    delay(5000);
}

void reconnect() {
    Serial.println("Device is trying to connect to server ");
    while (!client.connected()) {
        if (client.connect(deviceName)) {
        } else {
            delay(5000);
        }
    }
}

我使用Arduino Uno R3和ESP8266-01作為wifi連接器。 我必須讀取溫度數據並發送到Mosquitto，MongoDB和Raspberry Pi並接收有關特定條件的數據，因為我已經在Arduino中訂閱了一個主題。 我能夠從Arduino接收所有其他客戶的數據，但我無法接收Arduino中訂閱主題的數據。 但像MongoDB這樣的所有其他設備都能夠從Raspberry Pi接收數據。 我使用了Arduino Uno R3，ESP8266-01設備和liberary用於連接和發送/接收數據WiFiEsp.h，WiFiEspClient.h，WiFiEspUdp.h，SoftwareSerial.h，PubSubClient.h client.subscribe（“topic”）; 返回1還實現了回調函數但無法調用。

所以任何人都可以幫助我為什么我沒有在Arduino中訂閱主題消息？

我關注https://sonyarouje.com/2016/03/15/mqtt-communication-with-arduino-using-esp8266-esp-01/#comment-111773

Answer 1

你正在使用的庫有回調錯誤，因此你最好使用其他庫我的偏好是https://github.com/vshymanskyy/TinyGSM這個庫包括幾乎所有的SIM800變體（A，C，L， H，808），SIM900（A，D，908,968），ESP8266（安裝在arduino上），以太網屏蔽等的變體。它對我有用，因為同樣的問題在我看了差不多1-2周，但后者能夠全部收到訂閱消息，與通信模式無關（GSM，以太網，WiFi）