龐特與步進電機

Question

有沒有人在使用龐特的Big-Easy Kard和quick420板移動簡單的4引線雙極步進電機方面有任何經驗？ 我只是想嘗試使用包含的Arduino示例來控制步進電機，並將其移植過來，以便它們在Pontech環境中正常運行。 我嘗試轉換的代碼如下：

/* 
 Stepper Motor Control - one revolution

 This program drives a unipolar or bipolar stepper motor. 
 The motor is attached to digital pins 8 - 11 of the Arduino.

 The motor should revolve one revolution in one direction, then
 one revolution in the other direction.  


 Created 11 Mar. 2007
 Modified 30 Nov. 2009
 by Tom Igoe

 */

#include <Stepper.h>

const int stepsPerRevolution = 200;  // change this to fit the number of steps per revolution
                                     // for your motor

// initialize the stepper library on pins 8 through 11:
Stepper myStepper(stepsPerRevolution, 8,9,10,11);            

void setup() {
  // set the speed at 60 rpm:
  myStepper.setSpeed(60);
  // initialize the serial port:
  Serial.begin(9600);
}

void loop() {
  // step one revolution  in one direction:
   Serial.println("clockwise");
  myStepper.step(stepsPerRevolution);
  delay(500);

   // step one revolution in the other direction:
  Serial.println("counterclockwise");
  myStepper.step(-stepsPerRevolution);
  delay(500); 
}

我遇到的問題是我不知道如何正確地將定義了引腳8,9,10和11的零件轉換為具有電機引線的零件。 我知道它在.cpp文件中做到了這一點。 我在Stepper.h和Stepper.cpp下都包含了

/*
  Stepper.h - - Stepper library for Wiring/Arduino - Version 0.4

  Original library     (0.1) by Tom Igoe.
  Two-wire modifications   (0.2) by Sebastian Gassner
  Combination version   (0.3) by Tom Igoe and David Mellis
  Bug fix for four-wire   (0.4) by Tom Igoe, bug fix from Noah Shibley

  Drives a unipolar or bipolar stepper motor using  2 wires or 4 wires

  When wiring multiple stepper motors to a microcontroller,
  you quickly run out of output pins, with each motor requiring 4 connections. 

  By making use of the fact that at any time two of the four motor
  coils are the inverse  of the other two, the number of
  control connections can be reduced from 4 to 2. 

  A slightly modified circuit around a Darlington transistor array or an L293 H-bridge
  connects to only 2 microcontroler pins, inverts the signals received,
  and delivers the 4 (2 plus 2 inverted ones) output signals required
  for driving a stepper motor.

  The sequence of control signals for 4 control wires is as follows:

  Step C0 C1 C2 C3
     1  1  0  1  0
     2  0  1  1  0
     3  0  1  0  1
     4  1  0  0  1

  The sequence of controls signals for 2 control wires is as follows
  (columns C1 and C2 from above):

  Step C0 C1
     1  0  1
     2  1  1
     3  1  0
     4  0  0

  The circuits can be found at 
  http://www.arduino.cc/en/Tutorial/Stepper
*/

// ensure this library description is only included once
#ifndef Stepper_h
#define Stepper_h

// library interface description
class Stepper {
  public:
    // constructors:
    Stepper(int number_of_steps, int motor_pin_1, int motor_pin_2);
    Stepper(int number_of_steps, int motor_pin_1, int motor_pin_2, int motor_pin_3, int motor_pin_4);

    // speed setter method:
    void setSpeed(long whatSpeed);

    // mover method:
    void step(int number_of_steps);

    int version(void);

  private:
    void stepMotor(int this_step);

    int direction;        // Direction of rotation
    int speed;          // Speed in RPMs
    unsigned long step_delay;    // delay between steps, in ms, based on speed
    int number_of_steps;      // total number of steps this motor can take
    int pin_count;        // whether you're driving the motor with 2 or 4 pins
    int step_number;        // which step the motor is on

    // motor pin numbers:
    int motor_pin_1;
    int motor_pin_2;
    int motor_pin_3;
    int motor_pin_4;

    long last_step_time;      // time stamp in ms of when the last step was taken
};

#endif

現在進入Stepper.cpp

/*
  Stepper.cpp - - Stepper library for Wiring/Arduino - Version 0.4

  Original library     (0.1) by Tom Igoe.
  Two-wire modifications   (0.2) by Sebastian Gassner
  Combination version   (0.3) by Tom Igoe and David Mellis
  Bug fix for four-wire   (0.4) by Tom Igoe, bug fix from Noah Shibley  

  Drives a unipolar or bipolar stepper motor using  2 wires or 4 wires

  When wiring multiple stepper motors to a microcontroller,
  you quickly run out of output pins, with each motor requiring 4 connections. 

  By making use of the fact that at any time two of the four motor
  coils are the inverse  of the other two, the number of
  control connections can be reduced from 4 to 2. 

  A slightly modified circuit around a Darlington transistor array or an L293 H-bridge
  connects to only 2 microcontroler pins, inverts the signals received,
  and delivers the 4 (2 plus 2 inverted ones) output signals required
  for driving a stepper motor.

  The sequence of control signals for 4 control wires is as follows:

  Step C0 C1 C2 C3
     1  1  0  1  0
     2  0  1  1  0
     3  0  1  0  1
     4  1  0  0  1

  The sequence of controls signals for 2 control wires is as follows
  (columns C1 and C2 from above):

  Step C0 C1
     1  0  1
     2  1  1
     3  1  0
     4  0  0

  The circuits can be found at 

http://www.arduino.cc/en/Tutorial/Stepper


 */


#include "WProgram.h"
#include "Stepper.h"

/*
 * two-wire constructor.
 * Sets which wires should control the motor.
 */
Stepper::Stepper(int number_of_steps, int motor_pin_1, int motor_pin_2)
{
  this->step_number = 0;      // which step the motor is on
  this->speed = 0;        // the motor speed, in revolutions per minute
  this->direction = 0;      // motor direction
  this->last_step_time = 0;    // time stamp in ms of the last step taken
  this->number_of_steps = number_of_steps;    // total number of steps for this motor

  // Arduino pins for the motor control connection:
  this->motor_pin_1 = motor_pin_1;
  this->motor_pin_2 = motor_pin_2;

  // setup the pins on the microcontroller:
  pinMode(this->motor_pin_1, OUTPUT);
  pinMode(this->motor_pin_2, OUTPUT);

  // When there are only 2 pins, set the other two to 0:
  this->motor_pin_3 = 0;
  this->motor_pin_4 = 0;

  // pin_count is used by the stepMotor() method:
  this->pin_count = 2;
}


/*
 *   constructor for four-pin version
 *   Sets which wires should control the motor.
 */

Stepper::Stepper(int number_of_steps, int motor_pin_1, int motor_pin_2, int motor_pin_3, int motor_pin_4)
{
  this->step_number = 0;      // which step the motor is on
  this->speed = 0;        // the motor speed, in revolutions per minute
  this->direction = 0;      // motor direction
  this->last_step_time = 0;    // time stamp in ms of the last step taken
  this->number_of_steps = number_of_steps;    // total number of steps for this motor

  // Arduino pins for the motor control connection:
  this->motor_pin_1 = motor_pin_1;
  this->motor_pin_2 = motor_pin_2;
  this->motor_pin_3 = motor_pin_3;
  this->motor_pin_4 = motor_pin_4;

  // setup the pins on the microcontroller:
  pinMode(this->motor_pin_1, OUTPUT);
  pinMode(this->motor_pin_2, OUTPUT);
  pinMode(this->motor_pin_3, OUTPUT);
  pinMode(this->motor_pin_4, OUTPUT);

  // pin_count is used by the stepMotor() method:  
  this->pin_count = 4;
}

/*
  Sets the speed in revs per minute

*/
void Stepper::setSpeed(long whatSpeed)
{
  this->step_delay = 60L * 1000L / this->number_of_steps / whatSpeed;
}

/*
  Moves the motor steps_to_move steps.  If the number is negative, 
   the motor moves in the reverse direction.
 */
void Stepper::step(int steps_to_move)
{  
  int steps_left = abs(steps_to_move);  // how many steps to take

  // determine direction based on whether steps_to_mode is + or -:
  if (steps_to_move > 0) {this->direction = 1;}
  if (steps_to_move < 0) {this->direction = 0;}


  // decrement the number of steps, moving one step each time:
  while(steps_left > 0) {
  // move only if the appropriate delay has passed:
  if (millis() - this->last_step_time >= this->step_delay) {
      // get the timeStamp of when you stepped:
      this->last_step_time = millis();
      // increment or decrement the step number,
      // depending on direction:
      if (this->direction == 1) {
        this->step_number++;
        if (this->step_number == this->number_of_steps) {
          this->step_number = 0;
        }
      } 
      else { 
        if (this->step_number == 0) {
          this->step_number = this->number_of_steps;
        }
        this->step_number--;
      }
      // decrement the steps left:
      steps_left--;
      // step the motor to step number 0, 1, 2, or 3:
      stepMotor(this->step_number % 4);
    }
  }
}

/*
 * Moves the motor forward or backwards.
 */
void Stepper::stepMotor(int thisStep)
{
  if (this->pin_count == 2) {
    switch (thisStep) {
      case 0: /* 01 */
      digitalWrite(motor_pin_1, LOW);
      digitalWrite(motor_pin_2, HIGH);
      break;
      case 1: /* 11 */
      digitalWrite(motor_pin_1, HIGH);
      digitalWrite(motor_pin_2, HIGH);
      break;
      case 2: /* 10 */
      digitalWrite(motor_pin_1, HIGH);
      digitalWrite(motor_pin_2, LOW);
      break;
      case 3: /* 00 */
      digitalWrite(motor_pin_1, LOW);
      digitalWrite(motor_pin_2, LOW);
      break;
    } 
  }
  if (this->pin_count == 4) {
    switch (thisStep) {
      case 0:    // 1010
      digitalWrite(motor_pin_1, HIGH);
      digitalWrite(motor_pin_2, LOW);
      digitalWrite(motor_pin_3, HIGH);
      digitalWrite(motor_pin_4, LOW);
      break;
      case 1:    // 0110
      digitalWrite(motor_pin_1, LOW);
      digitalWrite(motor_pin_2, HIGH);
      digitalWrite(motor_pin_3, HIGH);
      digitalWrite(motor_pin_4, LOW);
      break;
      case 2:    //0101
      digitalWrite(motor_pin_1, LOW);
      digitalWrite(motor_pin_2, HIGH);
      digitalWrite(motor_pin_3, LOW);
      digitalWrite(motor_pin_4, HIGH);
      break;
      case 3:    //1001
      digitalWrite(motor_pin_1, HIGH);
      digitalWrite(motor_pin_2, LOW);
      digitalWrite(motor_pin_3, LOW);
      digitalWrite(motor_pin_4, HIGH);
      break;
    } 
  }
}

/*
  version() returns the version of the library:
*/
int Stepper::version(void)
{
  return 4;
}

Answer 1

我假設您是指quick240板，因為我找不到quick420。 如果我理解您的問題，您正在嘗試將步進功能引腳映射到MPIDE使用的數組值所標識的引腳嗎？

引腳8實際上是端口B，引腳0（PB0）轉換為C1IO3（原理圖上的RB0引腳）引腳9是端口B，引腳1轉換為C0IO3（引腳RB1）引腳10是PB2轉換為C1IO1（引腳RB2）引腳11是PB3轉換為C1IO0（引腳RB3）

C標識卡插槽，而IO號是插槽的插針。 陣列使用卡插槽和插針作為索引，因此應該可以最方便地使用那里。

為此，請使用Arduino引腳分配獲取引腳的端口號，然后使用quick240原理圖將端口和引腳轉換為卡插槽和IO編號。 如果願意，您可以向另一個方向翻譯。

Answer 2

看起來Arduino庫旨在直接激勵步進電機的繞組。 BigEasy具有Allegro步進驅動器芯片，該芯片需要步進和方向輸入。 他們是蘋果和橘子。 您可以將AccelStep庫與BigEasy一起使用，並且該庫已被移植到chipKIT。