OMAP3上的古怪SD卡是omap_hsmmc驅動程序嗎？

Question

由於某些原因，本來可以在任何Windows / Mac / Linux機器上使用的卡都不能在我們的嵌入式板上使用。 更糟糕的是，我們有相同的卡可以正常工作！ 我調查了omap_hsmmc驅動程序（內核2.6.32），並嘗試了各種更改，例如降低了啟用SPI模式的時鍾速率等，但是沒有運氣。

這是工作卡的輸出（先前的命令相同）：

mmc0: clock 24000000Hz busmode 2 powermode 2 cs 0 Vdd 16 width 2 timing 2
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new high speed SDHC card at address 59b4
mmcblk0: mmc0:59b4 SD    7.35 GiB 
 mmcblk0:
mmc0: starting CMD18 arg 00000000 flags 000000b5
mmc0:     blksz 512 blocks 8 flags 00000200 tsac 100 ms nsac 0
mmc0:     CMD12 arg 00000000 flags 0000049d
mmci-omap-hs mmci-omap-hs.0: mmc0: CMD18, argument 0x00000000
mmci-omap-hs mmci-omap-hs.0: IRQ Status is 1
mmci-omap-hs mmci-omap-hs.0: IRQ Status is 2
mmci-omap-hs mmci-omap-hs.0: mmc0: CMD12, argument 0x00000000
mmci-omap-hs mmci-omap-hs.0: IRQ Status is 3
mmc0: req done (CMD18): 0: 00000900 00000000 00000000 00000000
mmc0:     4096 bytes transferred: 0
mmc0:     (CMD12): 0: 00000b00 00000000 00000000 00000000
 p1 p2
mmci-omap-hs mmci-omap-hs.0: mmc_fclk: disabled
mmci-omap-hs mmci-omap-hs.0: mmc_fclk: enabled
mmci-omap-hs mmci-omap-hs.0: context was not lost
mmc0: starting CMD18 arg 000234cb flags 000000b5
mmc0:     blksz 512 blocks 2 flags 00000200 tsac 100 ms nsac 0
mmc0:     CMD12 arg 00000000 flags 0000049d
mmci-omap-hs mmci-omap-hs.0: mmc0: CMD18, argument 0x000234cb
mmci-omap-hs mmci-omap-hs.0: IRQ Status is 1
mmci-omap-hs mmci-omap-hs.0: IRQ Status is 2
mmci-omap-hs mmci-omap-hs.0: mmc0: CMD12, argument 0x00000000
mmci-omap-hs mmci-omap-hs.0: IRQ Status is 3

和壞卡：

mmc0: clock 24000000Hz busmode 2 powermode 2 cs 0 Vdd 16 width 2 timing 2
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new high speed SDHC card at address 59b4
mmcblk0: mmc0:59b4 SD    7.35 GiB 
 mmcblk0:
mmc0: starting CMD18 arg 00000000 flags 000000b5
mmc0:     blksz 512 blocks 8 flags 00000200 tsac 100 ms nsac 0
mmc0:     CMD12 arg 00000000 flags 0000049d
mmci-omap-hs mmci-omap-hs.0: mmc0: CMD18, argument 0x00000000
mmci-omap-hs mmci-omap-hs.0: IRQ Status is 1
mmci-omap-hs mmci-omap-hs.0: IRQ Status is 208002
mmci-omap-hs mmci-omap-hs.0: MMC IRQ 0x208002 : TC ERRI DCRC
mmci-omap-hs mmci-omap-hs.0: mmc0: CMD12, argument 0x00000000
mmci-omap-hs mmci-omap-hs.0: IRQ Status is 3
mmc0: req done (CMD18): 0: 00000900 00000000 00000000 00000000
mmc0:     0 bytes transferred: -84
mmc0:     (CMD12): 0: 00000b00 00000000 00000000 00000000
mmcblk0: retrying using single block read
mmc0: starting CMD17 arg 00000000 flags 000000b5
mmc0:     blksz 512 blocks 1 flags 00000200 tsac 100 ms nsac 0
mmci-omap-hs mmci-omap-hs.0: mmc0: CMD17, argument 0x00000000
mmci-omap-hs mmci-omap-hs.0: IRQ Status is 1
mmci-omap-hs mmci-omap-hs.0: IRQ Status is 208002
mmci-omap-hs mmci-omap-hs.0: MMC IRQ 0x208002 : TC ERRI DCRC
mmc0: req done (CMD17): 0: 00000900 00000000 00000000 00000000
mmc0:     0 bytes transferred: -84

看起來多塊DMA傳輸失敗（CMD18），因此驅動程序嘗試了單塊傳輸，但也失敗了。

我應該看什么？ 如果還有其他可以嘗試使用的驅動程序？ 另外，“ MMC IRQ 0x208002：TC ERRI DCRC”是什么意思？

Answer 1

問題是在4位數據模式下連接不良。