將連續數據寫入CSV文件

Question

我使用在python代碼來獲得的傳感器的數據，所述傳感器測量在不同的軸振動。 代碼工作很好，但我試圖自動寫入輸出數據到CSV文件。

這是我使用的代碼：

import smbus            
from time import sleep          

#some MPU6050 Registers and their Address
PWR_MGMT_1   = 0x6B
SMPLRT_DIV   = 0x19
CONFIG       = 0x1A
GYRO_CONFIG  = 0x1B
INT_ENABLE   = 0x38
ACCEL_XOUT_H = 0x3B
ACCEL_YOUT_H = 0x3D
ACCEL_ZOUT_H = 0x3F
GYRO_XOUT_H  = 0x43
GYRO_YOUT_H  = 0x45
GYRO_ZOUT_H  = 0x47


def MPU_Init():
    #write to sample rate register
    bus.write_byte_data(Device_Address, SMPLRT_DIV, 7)

    #Write to power management register
    bus.write_byte_data(Device_Address, PWR_MGMT_1, 1)

    #Write to Configuration register
    bus.write_byte_data(Device_Address, CONFIG, 0)

    #Write to Gyro configuration register
    bus.write_byte_data(Device_Address, GYRO_CONFIG, 24)

    #Write to interrupt enable register
    bus.write_byte_data(Device_Address, INT_ENABLE, 1)

def read_raw_data(addr):
    #Accelero and Gyro value are 16-bit
        high = bus.read_byte_data(Device_Address, addr)
        low = bus.read_byte_data(Device_Address, addr+1)

        #concatenate higher and lower value
        value = ((high << 8) | low)

        #to get signed value from mpu6050
        if(value > 32768):
                value = value - 65536
        return value


bus = smbus.SMBus(1)    # or bus = smbus.SMBus(0) for older version boards
Device_Address = 0x68   # MPU6050 device address

MPU_Init()

print (" Reading Data of Gyroscope and Accelerometer")

while True:

    #Read Accelerometer raw value
    acc_x = read_raw_data(ACCEL_XOUT_H)
    acc_y = read_raw_data(ACCEL_YOUT_H)
    acc_z = read_raw_data(ACCEL_ZOUT_H)

    #Read Gyroscope raw value
    gyro_x = read_raw_data(GYRO_XOUT_H)
    gyro_y = read_raw_data(GYRO_YOUT_H)
    gyro_z = read_raw_data(GYRO_ZOUT_H)

    #Full scale range +/- 250 degree/C as per sensitivity scale factor
    Ax = acc_x/16384.0
    Ay = acc_y/16384.0
    Az = acc_z/16384.0

    Gx = gyro_x/131.0
    Gy = gyro_y/131.0
    Gz = gyro_z/131.0


    print ("Gx=%.2f" %Gx, u'\u00b0'+ "/s", "\tGy=%.2f" %Gy, u'\u00b0'+ "/s", "\tGz=%.2f" %Gz, u'\u00b0'+ "/s", "\tAx=%.2f g" %Ax, "\tAy=%.2f g" %Ay, "\tAz=%.2f g" %Az)     
    sleep(2)

“”“””

現在的書寫順序我試圖用看起來是這樣的：

finaldata = { "Gx=%.2f" %Gx, u'\u00b0'+ "/s", "\tGy=%.2f" %Gy, u'\u00b0'+ "/s", "\tGz=%.2f" %Gz, u'\u00b0'+ "/s", "\tAx=%.2f g" %Ax, "\tAy=%.2f g" %Ay, "\tAz=%.2f g" %Az }
with open("accell.csv", "a")as output:
        writer = csv.writer(output, delimiter=",", lineterminiator = '\n')
        writer.writerow(finaldata)
sleep(2)

“”“”“””

但這種寫入CSV代碼不工作，我可以知道為什么嗎？

Answer 1

首先，添加導入CSV到你的代碼，然后用這部分csv文件寫：

import smbus            
from time import sleep       
import csv

#some MPU6050 Registers and their Address
PWR_MGMT_1   = 0x6B
SMPLRT_DIV   = 0x19
CONFIG       = 0x1A
GYRO_CONFIG  = 0x1B
INT_ENABLE   = 0x38
ACCEL_XOUT_H = 0x3B
ACCEL_YOUT_H = 0x3D
ACCEL_ZOUT_H = 0x3F
GYRO_XOUT_H  = 0x43
GYRO_YOUT_H  = 0x45
GYRO_ZOUT_H  = 0x47


def MPU_Init():
    #write to sample rate register
    bus.write_byte_data(Device_Address, SMPLRT_DIV, 7)

    #Write to power management register
    bus.write_byte_data(Device_Address, PWR_MGMT_1, 1)

    #Write to Configuration register
    bus.write_byte_data(Device_Address, CONFIG, 0)

    #Write to Gyro configuration register
    bus.write_byte_data(Device_Address, GYRO_CONFIG, 24)

    #Write to interrupt enable register
    bus.write_byte_data(Device_Address, INT_ENABLE, 1)

def read_raw_data(addr):
    #Accelero and Gyro value are 16-bit
        high = bus.read_byte_data(Device_Address, addr)
        low = bus.read_byte_data(Device_Address, addr+1)

        #concatenate higher and lower value
        value = ((high << 8) | low)

        #to get signed value from mpu6050
        if(value > 32768):
                value = value - 65536
        return value


bus = smbus.SMBus(1)    # or bus = smbus.SMBus(0) for older version boards
Device_Address = 0x68   # MPU6050 device address

MPU_Init()

print (" Reading Data of Gyroscope and Accelerometer")

while True:

    #Read Accelerometer raw value
    acc_x = read_raw_data(ACCEL_XOUT_H)
    acc_y = read_raw_data(ACCEL_YOUT_H)
    acc_z = read_raw_data(ACCEL_ZOUT_H)

    #Read Gyroscope raw value
    gyro_x = read_raw_data(GYRO_XOUT_H)
    gyro_y = read_raw_data(GYRO_YOUT_H)
    gyro_z = read_raw_data(GYRO_ZOUT_H)

    #Full scale range +/- 250 degree/C as per sensitivity scale factor
    Ax = acc_x/16384.0
    Ay = acc_y/16384.0
    Az = acc_z/16384.0

    Gx = gyro_x/131.0
    Gy = gyro_y/131.0
    Gz = gyro_z/131.0


    print ("Gx=%.2f" %Gx, u'\u00b0'+ "/s", "\tGy=%.2f" %Gy, u'\u00b0'+ "/s", "\tGz=%.2f" %Gz, u'\u00b0'+ "/s", "\tAx=%.2f g" %Ax, "\tAy=%.2f g" %Ay, "\tAz=%.2f g" %Az)

    finaldata = {"Gx=%.2f" % Gx, u'\u00b0' + "/s", "\tGy=%.2f" % Gy, u'\u00b0' + "/s", "\tGz=%.2f" % Gz,
                 u'\u00b0' + "/s", "\tAx=%.2f g" % Ax, "\tAy=%.2f g" % Ay, "\tAz=%.2f g" % Az}
    with open("\\test.csv", "a")as output:
        writer = csv.writer(output, delimiter=",")
        writer.writerow(finaldata)

    sleep(2)

Answer 2

@nimajv正確無誤，但我認為您忘記了以a+模式打開文件。

a + ：打開一個文件以進行附加和讀取。 如果文件存在，則文件指針位於文件的末尾。 該文件以追加模式打開。 如果該文件不存在，它將創建一個用於讀取和寫入的新文件-Python Files IO

當然，您還沒有創建文件時就是這種情況。 如果這樣做了，那么應該用真實的文件路徑替換他的代碼部分。 此外，您還應使用所需的任何真實路徑替換其虛擬路徑- \\\\test.csv 。 如果僅使用test.csv ，它將在運行腳本的目錄下創建文件（當然使用a+模式）。