Set linux time to millisecond precision

Question

I have an embedded Linux device that interfaces with another "master" device over a serial comm protocol. Periodically the master passes its date down to the slave device, because later the slave will return information to the master that needs to be accurately timestamped. However, the Linux 'date' command only sets the system date to within a second accuracy. This isn't enough for our uses.

Does anybody know how to set a Linux machine's time more precisely than 1 second?

Answer 1

The settimeofday(2) method given in other answers has a serious problem: it does exactly what you say you want. :)

The problem with directly changing a system's time, instantaneously, is that it can confuse programs that get the time of day before and after the change if the adjustment was negative. That is, they can perceive time to go backwards.

The fix for this is adjtime(3) which is simple and portable, or adjtimex(2) which is complicated, powerful and Linux-specific. Both of these calls use sophisticated algorithms to slowly adjust the system time over some period, forward only, until the desired change is achieved.

By the way, are you sure you aren't reinventing the wheel here? I recommend that you read Julien Ridoux and Darryl Veitch's ACM Queue paper Principles of Robust Timing over the Internet . You're working on embedded systems, so I would expect the ringing in Figure 5 to give you cold shivers. Can you say "damped oscillator?" adjtime() and adjtimex() use this troubled algorithm, so in some sense I am arguing against my own advice above, but the Mills algorithm is still better than the step adjustment non-algorithm. If you choose to implement RADclock instead, so much the better.

Answer 2

The settimeofday() system call takes and uses microsecond precision. You'll have to write a short program to use it, but that is quite straightforward.

struct timeval tv;
tv .tv_sec = (some time_t value)
tv .tv_usec = (the number of microseconds after the second)
int rc = settimeofday (&tv, NULL);
if (rc)
        errormessage ("error %d setting system time", errno);

Answer 3

• You can use the settimeofday(2) system call; the interface supports microsecond resolution.

   #include <sys/time.h> int gettimeofday(struct timeval *tv, struct timezone *tz); int settimeofday(const struct timeval *tv, const struct timezone *tz); struct timeval { time_t tv_sec; /* seconds */ suseconds_t tv_usec; /* microseconds */ }; 

• You can use the clock_settime(2) system call; the interface provides multiple clocks and the interface supports nanosecond resolution.

   #include <time.h> int clock_getres(clockid_t clk_id, struct timespec *res); int clock_gettime(clockid_t clk_id, struct timespec *tp); int clock_settime(clockid_t clk_id, const struct timespec *tp); struct timespec { time_t tv_sec; /* seconds */ long tv_nsec; /* nanoseconds */ }; CLOCK_REALTIME System-wide real-time clock. Setting this clock requires appropriate privileges. CLOCK_MONOTONIC Clock that cannot be set and represents monotonic time since some unspecified starting point. CLOCK_MONOTONIC_RAW (since Linux 2.6.28; Linux-specific) Similar to CLOCK_MONOTONIC, but provides access to a raw hardware-based time that is not subject to NTP adjustments. CLOCK_PROCESS_CPUTIME_ID High-resolution per-process timer from the CPU. CLOCK_THREAD_CPUTIME_ID Thread-specific CPU-time clock. 

  This interface provides the nicety of the clock_getres(2) call, which can tell you exactly what the resolution is -- just because the interface accepts nanoseconds doesn't mean it can actually support nanosecond-resolution. (I've got a fuzzy memory that 20 ns is about the limits of many systems but no references to support this.)

Answer 4

If you're running an IP-capable networking protocol over the serial link (something like, ooh, PPP for example), you can just run an ntpd on the "master" host, then sync time using ntpd or ntpdate on the embedded device. NTP will take care of you.