使用 Verilog 的 Quartus II 寄存器的奇怪行为

Question

我正在使用 Quartus II 和 Verilog 基于 MIPS32 创建我自己的处理器。 一切正常，直到我的寄存器突然停止工作（我不记得对代码进行了任何修改）。 我可能犯了一些错误，但我似乎无法找到它。

我已经尝试使用旧版本的代码（100% 工作）但错误仍然存​​在，即使我正在测试与系统其余部分隔离的寄存器。 我也试过删除 Quartus 的临时文件并重新编译但没有成功。

    module RegFile
    (
        output [31:0] Debug2,       //Outputs Reg 2
        output [31:0] Debug3,       //Outputs Reg 3
        input Reset,                //Makes sure Reg 0 is always 0
        input Slow_Clock,           //Write Clock
        input Fast_Clock,           //Read Clock
        input Reg_Write,            //Write to Reg Flag
        input [31:0] Write_Data,    //Data that will be written in the Reg selected by Reg_WR
        input [5:0] Reg_1,          //First Register Selection (Read)
        input [5:0] Reg_2,          //Second Register Selection (Read)
        input [5:0] Reg_WR,         //Third Register Selection (Read or Write)
        output reg [31:0] Data_1,   //Data that will outputted by the Reg selected by Reg_1
        output reg [31:0] Data_2,   //Data that will outputted by the Reg selected by Reg_2
        output reg [31:0] Data_3    //Data that will outputted by the Reg selected by Reg_WR
    );


    reg [31:0] DataReg[63:0];       //64x 32bit Register

    assign Debug2 = DataReg[2]; //Hardwired Reg2 (for testing)
    assign Debug3 = DataReg[3]; //Hardwired Reg3 (for testing)

    always @ (posedge Fast_Clock)   //Reads from Registers at posedge Read Clock
    begin
        Data_1 <= DataReg[Reg_1];
        Data_2 <= DataReg[Reg_2];
        Data_3 <= DataReg[Reg_WR];
    end

    always @ (negedge Slow_Clock) //Writes on Registers at negedge Write Clock
    begin
        if (Reset)
        begin
            DataReg[0] <= 32'b00000000_00000000_00000000_00000000; //Forces Reg0 to be 0 when Reset is activated
        end
        else if (Reg_Write && (Reg_WR != 0)) //If you are writing to some register and this register isn't Reg0...
        begin
            DataReg[Reg_WR] <= Write_Data; //...write to the register selected by Reg_WR
        end
    end

    endmodule

我希望最终结果是寄存器 2 上的数字 3 和寄存器 3 上的数字 4，但是，如您所见，寄存器 2 以数字 4 结尾，而寄存器 3 以数字 0 结尾。

Answer 1

我想到了。

在下一个时钟写入和加载新值时出现不一致。

我通过创建两个辅助来修复它。 在写入和更新值之前保存 Write_Data 和 Reg_WR 的变量。 我使用了一个更快的时钟来保持这些辅助。 变量更新。

这是我找到的解决方案：

module RegFile
(
    //output [31:0] Debug2,       //Outputs Reg 2
    output [31:0] Debug3,       //Outputs Reg 3
    input Reset,                //Makes sure Reg 0 is always 0
    input Slow_Clock,             //Write Clock
    input Fast_Clock,
     input Reg_Write,            //Write to Reg Flag
    input [31:0] Write_Data,    //Data that will be written in the Reg selected by Reg_WR
    input [5:0] Reg_1,          //First Register Selection (Read)
    input [5:0] Reg_2,          //Second Register Selection (Read)
    input [5:0] Reg_WR,         //Third Register Selection (Read or Write)
    output [31:0] Data_1,         //Data that will outputted by the Reg selected by Reg_1
    output [31:0] Data_2,       //Data that will outputted by the Reg selected by Reg_2
    output [31:0] Data_3        //Data that will outputted by the Reg selected by Reg_WR
);

reg [31:0] RegBank[63:0];

reg [31:0] Aux_WD;
reg [5:0] Aux_Reg;

assign Data_1 = RegBank[Reg_1];
assign Data_2 = RegBank[Reg_2];
assign Data_3 = RegBank[Reg_WR];

//assign Debug2 = RegBank[2];
assign Debug3 = RegBank[3];

always @ (negedge Fast_Clock)
begin
    Aux_WD <= Write_Data;
    Aux_Reg <= Reg_WR;
end

always @ (negedge Slow_Clock)
begin
    if (Reset)
    begin
        RegBank[0] <= {32{1'b0}};
    end
    else if (Reg_Write && (Aux_Reg != 6'b000000))
    begin
        RegBank[Aux_Reg] <= Aux_WD;
    end
end

endmodule